technical data sheet 6 lake street, lawrence, ma 01841 1-800-446-1158 / (978) 620-2600 / fax: (978) 689-0803 website: http://www.microsemi.com high reliability schottky rectifier qualified per mil-prf-19500/553 ? schottky barrier rectifier ? 600 amps surge rating ? low forward voltage ? reverse energy tested t4-lds-0137 rev. 1 (091728) page 1 of 3 devices levels 1n6391 jan jantx jantxv jans absolute maximum ratings (t c = +25c unless otherwise noted) parameters / test conditions symbol value unit peak repetitive reverse voltage v rwm 45 v peak working reverse voltage v rrm 45 v average forward current, t c = 125 i f 25 a peak surge forward current @ t p = 8.3ms, half sinewave, t a = 100c i fsm 600 a thermal resistance, junction to case r jc 2.0 c/w operating junction temperature range t j -55c to 175c c storage temperature range t stg -55c to 175c c electrical characteristics (t a = +25c, unless otherwise noted) parameters / test conditions symbol min. max. unit forward voltage i fm = 5a, t j = 25c* v fm 0.5 v forward voltage i fm = 50a, t j = 25c* v fm 0.68 v reverse current v rm = 45v, t j = 25c i rm 1.5 ma reverse current v rm = 45v, t j = 125c* i rm 40 ma reverse current v rm = 45v, t c = 175c* i rm 220 ma reverse current v rm = 45v, t c = -55c* i rm 400 ma reverse energy l = 260 h 1% duty cycle i r(ov) 2 a capacitance v r = 5v, f = 1mhz, 100khz f 1mhz c t 2000 pf * pulse test: pulse width 300 sec, duty cycle 2% note: do-203aa (do-4)
technical data sheet 6 lake street, lawrence, ma 01841 1-800-446-1158 / (978) 620-2600 / fax: (978) 689-0803 website: http://www.microsemi.com high reliability schottky rectifier t4-lds-0137 rev. 1 (091728) page 2 of 3 graphs figure 3 typical junction capacitance figure 1 typical forward characteristics figure 4 forward current derating figure 2 typical reverse characteristics
technical data sheet 6 lake street, lawrence, ma 01841 1-800-446-1158 / (978) 620-2600 / fax: (978) 689-0803 website: http://www.microsemi.com high reliability schottky rectifier t4-lds-0137 rev. 1 (091728) page 3 of 3 package dimensions dimensions inches millimeters ltr min max min max notes c .250 6.35 7 cd .265 .424 6.73 10.77 8 ch .300 .405 7.62 10.29 c1 .018 .065 0.46 1.65 7 hf .403 .437 10.24 11.10 8 ht1 .075 .175 1.91 4.45 ht2 .060 1.53 6 oah .600 .800 15.24 20.32 sd 5 sl .422 .453 10.72 11.51 su .078 1.98 4 ud .163 .189 4.14 4.80 t .060 .103 1.52 2.62 notes: 1. dimensions are in inches. 2. millimeters are given for general information only. 3. units must not be damaged by torque of 15 inch-pounds applied to .10-32 unf-2b nut assembled on thread. 4. length of incomplete or undercut threads of ud. 5. maximum pitch diameter of plated threads shall be basic pitch diameter .1697 inch (4.31 mm), reference fed-std-h28, ?screw-thread standards for federal services?. 6. a chamfer or undercut on one or both ends of the hex portion is optional; minimum base diameter at seati ng plane .403 inch (10.24 mm). 7. the angular orientation and peripheral configuration of terminal 1 is undefined, however, the major surfaces over dimensions c and c1 shall be flat. 8. the cathode is connected to terminal 2. 9. in accordance with asme y14. 5m, diameters are equivalent to x symbology. physical dimensions (do-4)
|
